| |
|
|
|
|
 |
| |
ALUCA’s customized van racking systems consist of different unit heights, depths and widths (A, B, C).
All fitted elements used in practice (1- 8) are available in these basic dimensions.
The units can be planned and installed in accordance with our customer’s precise criteria and requirements. There is almost no limit to what ALUCA’s in-vehicle systems can provide.
SUPPORT FRAMES
• Heavy-duty aluminium design
with standardized pre-punched
holes for all components with a
grid of 25 mm
• 13 unit heights:
von 250 mm to 1350 mm
• 5 unit depths:
250 mm, 320 mm,
420 mm, 520 mm, 735 mm
• Width of support frame 30 mm
SIDE WALL
• To cover the equipment block
at the side
• Pre-punched holes 34 x 34 mm
for additional tool holders
DRAWER
• With an ergonomic central lock and safety latch on both sides
• Can be provided with a lock as an option; lock can also be retrofitted
• Trim panel made of anodized aluminium extruded profiles
• Scope for division using mats, dividers and plastic bin sets for drawers
• 4 unit widths:
360 mm, 460 mm, 705 mm, 950 mm
• Drawer heights:
100 mm, 150 mm, 200 mm 250 mm, 300 mm,
• Full drawer pullout with arrester if opened completely
• Drawer pullout can be divided to remove full drawer
SHELF COMPARTMENT
BASE
• 6 unit widths:
360 mm, 460 mm, 705 mm
950 mm, 1195 mm, 1440 mm
• Edge raised 100 mm at side
and back
• Use with flap or shelf bracket
TROUGH TRAY
• 2 variants: 1. Back: 100 mm,
Front 100 mm;
2. Back 100 mm and front
50 mm high
• 6 unit widths:
360 mm, 460 mm, 705 mm,
950 mm, 1195 mm, 1440 mm
• 4 unit depths:
250 mm, 320 mm, 420 mm,
520 mm
• Trough upper edge with
integrated system strip
to hold dividers
DOOR ELEMENT
• Lockable door element made of
aluminium
• Door arrester possible at left or
right
• Field width: 460 mm
• 11 heights: 400 - 1300 mm
SHELF FLAPS
• Made of torsion-free anodized
aluminium extruded profile
• For shelf compartments, shelf
and shelf compartment base
• With shelf and compartment
base, swivels down fully
• Heights 125 and 175 mm
Actual projection:
100 and 150 mm
PULLOUT FOR CASE
• For aluminium or plastic case
• One-hand operation and safety
latch at both sides
• Field width: 460 mm
• also available with lock
• Lock can also be retrofitted
SHELF
• 4 unit widths
(unit depth 715 mm and 735 mm
in 3 unit widths) with width
950 mm incl. shelf reinforcement
• Installed at an angle or rotated,
also as a storage compartment
for a small parts case, storage
magazines and systainer (applies
to field widths 360, 460, 705 mm)
• As a top closing element
for drawer preassembled
drawer units.
UNIT HEIGHTS
• 13 unit heights:
from 250 mm to 1350 mm
UNIT DEPTHS
• 5 unit depths:
250 mm, 320 mm,
420 mm, 520 mm, 735 mm
FIELD WIDTHS
• 6 unit widths:
360 mm, 460 mm, 705 mm,
950 mm, 1195 mm, 1440 mm
|
|
|
|
